ASTM A192 Seamless Boiler Tubes Shipment
ASTM A192 / A192M, ASME SA192 / SA192M is the standard applicable to Seamless carbon steel boiler tubes for High-pressure service
Shipment information:
Products: ASTM A192 Seamless Boiler Steel Tubes.
Producing Type: Cold Drawn
Destination: Singapore
Standard: ASTM A192
Steel Grade: A192
Size: OD. 57mm x W.T. 3.2mm (Min) x Length 6096mm
Quantity: 50tons
Supplier: CTS TUBES
Shipping time: 15-April-2019
ASTM A192 Standard covers minimum-wall thickness, seamless carbon steel boiler and superheater tubes for high- pressure service.
Heat Treatment: Cold- finished tubes shall be heat treated after the final cold-finishing at a temperature of 1200°F [650°C] or higher.
Test requirement:
ASTM A192 Tube Chemical Compositions
Chemical Components (%) | |||||||
C | Si | Mn | P | S | Mo | Cr | V |
0.06-0.18 | ≤0.25 | 0.27-0.63 | ≤0.035 | ≤0.035 | / | / | / |
Click to download the details of ASTM A192 Seamless Boiler Tubes shipment.
ASTM A192 Tube Mechanical Tests Required
Mechanical properties | |||
Tensile Strength (Mpa) |
Yield Strength (Mpa) |
Elongation (%) |
Hardness (HRB) |
≥325 | ≥180 | ≥35 | ≤77 |
ASTM A192 Tube Wall Thickness Tolerance
Seamless, Cold-Finished Tubes | ||
Outside Diameter In. (mm) |
Wall thickness Tolerance % | |
Over (+) | Under (-) | |
1 ½ (38.1) and under |
20 | 0 |
Over 1½ (38.1) | 22 | 0 |
ASTM A192 Tube Outside Diameter Tolerance
Cold-Finished Seamless Tubes | ||
Outside Diameter In. (mm) |
Permissible Variations In. (mm) | |
Over (+) | Under (-) | |
Under 1 (25.4) | 0.004 (0.1) | 0.004 (0.1) |
1 to 1 ½ (25.4 to 38.1), Incl | 0.006 (0.15) | 0.006 (0.15) |
Over 11⁄2 to 2 [38.1 to 50.8], Excl | 0.008 (0.2) | 0.008 (0.2) |
2 to 21⁄2 [50.8 to 63.5], Excl | 0.010 (0.25) | 0.010 (0.25) |
21⁄2 to 3 [63.5 to 76.2], Excl | 0.012 (0.3) | 0.012 (0.3) |
ASTM A192 Tube Cut Length Tolerance
Cold-Finished Seamless Tubes | |||
Outside Diameter, In.(mm) |
Cut Length, in.(mm) | ||
Over (+) | Under (-) | ||
All Sizes | 3⁄16 [5] | 0 [0] | |
Under 2 [50.8] | 1⁄8 [3] | 0 [0] | |
2 [50.8] and over | 3⁄16 [5] | 0 [0] | |
Under 2 [50.8] | 1⁄8 [3] | 0 [0] | |
2 [50.8] and over | 3⁄16 [5] | 0 [0] | |
These permissible variations in length apply to tubes before bending. They apply to cut lengths up to and including 24 ft [7.3 m]. For lengths greater than 24 ft [7.3 m], the above over-tolerances shall be increased by 1⁄8 in. [3 mm] for each 10 ft [3 m] or fraction thereof over 24 ft or 1⁄2 in. [13 mm], whichever is the lesser. | |||
ASTM A192 Tube Hydrostatic Test Pressures
Each tube shall be subjected to the hydrostatic pressure test, or instead of this test, a nondestructive test may be used when specified by the purchaser.
Hydrostatic Test Pressures | |
Outside Diameter of Tube, in. [mm] | Hydrostatic Test Pressure, psi [MPa] |
Under 1 [25.4] | 1000 [7] |
1 to 11⁄2 [25.4 to 38.1], excl | 1500 [10] |
11⁄2 to 2 [38.1 to 50.8], excl | 2000 [14] |
2 to 3 [50.8 to 76.2], excl | 2500 [17] |
ASTM A192 Flattening Test
One flattening test shall be made on specimens from each end of two tubes selected from each lot or fraction thereof.
ASTM A192 Flaring Test
One flaring test shall be made on specie- men from each end of two tubes selected from each lot or fraction thereof. These tubes shall be selected apart from those used for the flattening test.
Inspection Photos:
Get in Touch
If you are interested in our products or service, please contact us now.
Tel.: +86 185 5109 0083 | E-mail: [email protected]